Abstract: Through the reformation of centrifugal pump impeller structure, increasing the flow, raising the lift, meeting the production requirements.
Key words: Centrifugal pump retrofit flow rate increase
The decarburization system in our workshop adopts the hot potash method to remove CO2 from the low volatility gas to provide a qualified hydrogen-nitrogen mixture for ammonia synthesis and at the same time provides CO2 gas with purity greater than 98% for urea production. The solution circulation mainly by decarbonization pump to provide energy.
Over the years, the system load is low, the required flow is less than 200m3 / h, far less than the design capacity of the pump 480m3 / h. In order to reduce power consumption, in 92 years its impeller cylindrical cutting, the effect is good. However, since the first phase of the 81 August fertilizer program was put into operation in 1999, the required flow rate increased to 240 m3 / h. According to the reconstruction team's calculation, the large pump impeller was restored to the original large impeller, basically meeting the production requirements at that time. When the second phase of fertilizer "8 · 13" was put into operation in 2001, the required flow rate increased to 280m3 / h. At this moment, the problem is exposed, the flow of large pump can not be increased any more, the liquid-liquid phenomenon appears in the atmospheric tower, Production is very unstable, the load is difficult to increase. In order to solve this bottleneck that restricts production, the workshop and the maneuver department formed a special research personnel.
improvement measures
Pump volute erosion wear problems, due to the difficulty of repairing, do not deal with. In order to reduce the backflow, strictly control the impeller wear ring and pump wear ring gap at 0.50 ~ 0.68mm, but at the same time on the pump shaft stiffness, straightness and the manufacturers conducted a coordinated, in strict accordance with the technical requirements. Such as quenching and tempering should be done to the regular manufacturers, and a written report. After each overhaul, should use the dial indicator to find the correct control tolerance is less than 0.05mm, to ensure that the pump shaft concentric with the motor shaft.
Reasonable deployment of system heat balance in production, as far as possible to reduce the temperature of imported lye, the maximum shall not exceed 108 ℃.
Aiming at the impeller structure problem, Yangzhou Lianxing Pump Co., Ltd. commissioned by the Department of Mechanical Engineering to recalculate the design without changing the assembly size in two steps. The first step is to improve the blade involute, Welded type, eliminating the bumpy inner surface after casting defect. The second step in the intensity of the allowable range of accounting, the appropriate reduction of the thickness of the blade and the front and rear cover, increasing the size of the entrance.
Transformation effect
After the new impeller put into operation, the operation is smooth and the effect is good. After the first improvement of the impeller structure, the flow rate is increased from 240m3 / h to 270m3 / h, basically meeting the production requirements. After the second improvement, the flow rate is increased To 310m3 / h, higher than the 280m3 / h currently required to sustain high-load production. In the case of unstable production, it is easy to adjust the process, increase the flexibility of operation, increase the capacity of absorbing CO2, eliminate the phenomenon of blocking the two towers and eliminate a big bottleneck of the restriction of the workshop control load. Foundation.
PVC Sign Board named foam sign board by some other people .They are widely used indoor and outdoor signs .Most are for the display case and wall and other style displays . We can provide two kinds of printing process on the pvc boards ,one is digital printing on the sticker ,then stick them on the board ,this way is economic and you can change the graphic if the size is not too large ,you can apply the stickers on the board times .The other one is uv flatbed printing on the pvc sign boards , this way you can not change the printed graphic ,the uv ink on the board is not washable and it will be strong on the surface on the board ,concave-convex printing is available for our uv printing on the boards . So it will appear to 3D effect ,you can touch with hand for the concave- convex.
Specification :
1. largest size seamless is 122*244cm
2. die – cut is available
3. single side and double sided printing optional
4. no MOQ
5. digital printing and uv printing is available
6. thickness of the pvc board :1- 20 mm optional
7. package :1 pcs / opp bag
8. waterpoof and uv resistant
9. different density (hardness )to choose ,the common is 0.5 and the hard one is 0.7 ,we even can provide 0.9 density .
10. different color of the pvc board optional (except for transparent )
11. sample cost : free small sample available
12. sample date :2-3 days
13. production ability : 1000 per square meters per day
14. payment : 30% deposit and balance against shippment with Bank Transfer ,Paypal ,L/C ,Western Union
For more questions,please contact with us ( 0086 13427921037 ).
Foam Sign Boards,PVC Banners,PVC Sign Boards,Custom PVC Sign Boards
Golden Mouth Advertising (H.K)Co.,Ltd. ( Jie Da Advertisement Co.,Ltd) , https://www.advertisingflagbannerss.com